產品品牌：三良 產品型號：SLWB-1T-1800*1800mm 三良汽車尾板簡介： 佛山市三良機械設備有限公司生產的三良牌汽車尾板是安裝于貨車和各種密閉車輛尾部的一種以車載蓄電池為動力的液壓起重裝卸設備?？纱蠓忍岣哌\輸及裝卸效率，是現代化物流運輸?shù)谋貍湓O(shè)備之一。三良尾板現已廣泛應用于紙品、印刷、五金、化工、模具、工業氣體、電子、電器、金融、郵政、物流、運輸?shù)缺姸囝I(lǐng)域，深受廣大用戶好評。三良尾板也叫汽車升降尾板、裝卸尾板、起重尾板、液壓尾板。San Liang Automobile Tail Description: Foshan san liang Machinery Equipment Co., Ltd. San liang brand vehicles produced by the end plate is installed in trucks and a variety of enclosed vehicles to the rear of a car battery-powered hydraulic lifting handling equipment. Can greatly improve the efficiency of transport and handling, is a modern logistics and transport, one of the essential equipment. San liang tail plate is now widely used in paper products, printing, hardware, chemicals, mold, industrial gas, electronics, electrical appliances, financial services, postal services, logistics, transportation and many other areas, well received by consumers. San liang, also known as automobile tail plate lifting tail board, tail plate loading and unloading, lifting tail plate, hydraulic tailgate.三良汽車尾板特點：1.液壓缸均采用鍍鎳活塞桿及防塵圈,密封系統采用多層組合密封，性能穩定不漏油。2.液壓站內置流量控制閥，可調校升降及翻轉速度。3.內置三道保護開關，當汽車電路短路、電瓶電壓偏低或電流偏大、尾板超載等情況出現時可有效避免造成電路或馬達的燒毀。4.另配置過橋分隔尾板與車廂尾門，避免車廂尾門長期碰撞導致?lián)p毀。5．配置有安全保護系統，當尾板升與車廂平齊時，系統自動切斷電源。6．尾板的核心---動力系統采用原裝進口動力配置單元。7.動力系統、密封件、液壓管路均原裝進口，安全可靠，故障率低。8.電控箱采用四位按鈕獨特的人性化設計單鍵操作，方便快捷。9.采用車載電源供電，綠色環保。10.采用五缸液壓驅動系統，全自動操作，各油缸通過電控操作便可實現順序動作，可隨時根據裝卸貨物需要調節尾板的傾斜角度，并具有相對位置的自動智能記憶功能，適合安裝于各類型貨車。San Liang vehicle liftgate features: 1. Hydraulic cylinders are used nickel-plated piston rod and the dust ring, sealing system uses multi-layer sealing, stable performance, no leakage. 2. Hydraulic station built-in flow control valve, adjustable lifting and turning speed. 3. Built-in three-protect switch, when the vehicle a short circuit, low battery voltage or current is too large, tail plate overload occurs can effectively avoid the circuit or the motor burning. 4. The other configuration separated by the end of the bridge plate and car tail gate, tail gate to prevent car collisions result in long-term5. Equipped with safety protection system, when the tail plate l flush with the car, the system automatically shut off power. 6. Transom core --- South Korea imported power system using power unit. 7. Power system, seals, hydraulic pipes are imported, safe and reliable, failure rate is low. 8. Electric control box with four buttons a unique user-friendly design of one-touch operation, convenient and quick. 9. Use of vehicle power supply, green environmental protection. 10. With five-cylinder hydraulic drive system, fully automatic, electronically controlled operation of the fuel tank can be achieved through the sequence of action, may at any time according to loading and unloading of goods necessary to readjust the tilt angle of the end plate, and has the relative position of the automatic intelligent memory function, suitable for installation in all types of vehicles.三良汽車尾板分類（ San liang Automobile Tail Category）：三良汽車尾板主要可分為: 1. 懸臂式尾板:結構較復雜，載重量大，板面角度可調節；適用于各種箱式貨車、敞車、郵政、銀行等特種運輸車輛；其適用范圍最為廣泛。 2.垂直式尾板:結構簡單、安裝簡便、載重量較小。適用于各種車型。主要用于機場配餐車和氣瓶運輸車等。 3.搖臂式尾板:結構簡單，自重較輕，載重量較小，安裝簡便。適用于輕型貨車，主要用于氣瓶、桶、罐類運輸。San liang vehicle liftgate can be divided into: 1. Cantilever tail plate: structure more complex load large plate surface angle can be adjusted; applicable to all kinds of box-type trucks, gondola car, postal services, banks and other special transportation vehicles; its application to the widest range. 2. Vertical tail plate: simple structure, easy installation, a smaller load. Applicable to a variety of models. Primarily for use in airport catering trucks and other vehicles and gas cylinders. 3. Rocker-style tail plate: simple structure, light weight, load small, easy to install. For light trucks, mainly used for gas cylinders, drums, cans of transport.三良汽車尾板安裝注意事項:1、汽車車廂尾部不需做腳踏板載重量大于3噸的貨車尾燈應平置。2、汽車尾燈上端應低于車廂底板至少250mm。3、3噸以下的貨車尾燈應豎置，上端應該低于車廂底板至少250mm。4、汽車車廂底板與其相連的后端槽鋼應該在同一水平面內，不應留下臺階。5、汽車車廂下邊的門扣應做成彎鉤，扣在槽鋼相應小孔上，槽鋼上不應做凸出的門扣。6、汽車車廂后檔板中間部分約1000mm，保持全空。San liang vehicle liftgate Installation Notes: 1, cars do not need to do the rear pedal car load of greater than 3 tons of truck taillights should be set flat. 2, car tail lights should be below the upper compartment floor at least 250mm. 3,3 tons truck taillights should be set vertical, the upper floor should be less than the carriage of at least 250mm. 4, vehicle compartment floor with its back-channel should be connected to the same horizontal plane, the steps should not be left behind. 5, auto car below the door of deduction should be made of hook, buckle the corresponding holes in the channel, the channel should not be doing the door protruding buckle. 6, the middle part of the vehicle compartment tailgate is about 1000mm, to keep the whole space.三良汽車尾板技術參數尾板型號XL-TG-700XL-TG-1000XL-TG-1000AXL-TG-1500AXL-TG-2000AXL-TG-2500A額定載重700KG1000KG1000KG1500KG2000KG2500KG自身重量250KG300KG350KG400KG500KG550KG面板規格(高x寬)1800x12001600x8001800x12001600x8001800x16001700x16001800x16002000x16001700x16002000x18002100x18002200x18001600x15002300x18002400x18002500x1850電機動力DC12V-24V/100AH-16AH電機功率1.6kw1.6kw2kw2kw3kw開關門方式半自動機械式全自動電控式支架臂長700700/750750/900900/1000支架內寬500900900/10501050適用廂底高度700-950800/10001000/1500平均升降速度80mm/s選用油料普通液壓油(一般選用32#、46#或68#)落地工作傾角50-80(與面板高度成反比)Tail plate Model XL-TG-700 XL-TG-1000 XL-TG-1000A XL-TG-1500A XL-TG-2000A XL-TG-2500A Rated Load 700KG 1000KG 1000KG 1500KG 2000KG 2500KG Own weight 250KG 300KG 350KG 400KG 500KG 550KG Panel Size (H x W) 1800x1200 1600x800 1800x1200 1600x800 1800x1600 1700x1600 1800x1600 2000x1600 1700x1600 2000x1800 2100x1800 2200x1800 1600x1500 2300x1800 2400x1800 2500x1850 Electric Power DC12V-24V/100AH-16AH Motor Power 1.6kw 1.6kw 2kw 2kw 3kw Semi-automatic mechanical door switch mode automatic electric control type Bracket arm length 700 700/750 750/900 900/1000 Stent W 500 900 900/1050 1050 Applicable to the car at the end of a high degree of 700-950 800/1000 1000/1500 The average lifting speed of 80mm / s Ordinary use of oil hydraulic oil (generally choose 32 #, 46 # or 68 #) Floor work dip 50-80 (with the panel height is inversely proportional to)